BIGTREETECH DIRECT TFT35 E3 V3.0 Touch Screen /12864 LCD Display Control 3.5 inch Support WiFi Modle 3D Printer Parts for SKR V1.3 PRO Mini E3 Ender3 CR-10


BIGTREETECH TFT35-E3 V3.0 is a medium size, dual-mode, ultra-clear 3D printing machine display launched by the 3D printing team of
Shenzhen BIGTREE Technology CO., LTD., which can perfectly replace the original LCD screen of Ender3 printer.

Firmware: https://github.com/bigtreetech/BTT-TFT35-E3-V3.0

1.Product Parameters:
Appearance size:93*87mm
Installation size:Perfectly replace the original LCD screen of Ender3 printer,detail information please check TFT35-E3 V3.0 SIZE
Microprocessor:STM32F207VCT6
Power Input:DC 5V
SD card logic voltage:3.3V and 5V(Such as: support MEGA2560 main control chip motherboard, higher compatibility)

2.Product characters:
1)ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz;
2)Upgrade the firmware by SD card. It is easy and convenient to operate.
3)This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode.
4)Serial port screen mode supports two printing modes: SD card and U disk.
5)Reserve WIFI port, and WIFI function is realized by external WIFI module;
6)Reserve the extension port of filament breaking detection (FIL-DET);
7)Reserve the extension port of automatic shutdown after printing (PS-ON);
8)LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) ;
9)TFT touch screen mode:serial port screen RS232 port;
10)2 sets of UART serial port extension ports are reserved for DIY use.

Product Features

  • 1)ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz;
  • 2)Upgrade the firmware by SD card. It is easy and convenient to operate.
  • 3)This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode.
  • 4)LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) ;
  • 5)SD card logic voltage:3.3V and 5V(Such as: support MEGA2560 main control chip motherboard, higher compatibility)

Visit The Website For More Information…

BIQU 3D Printer Part TFT 2.4 Inch Touch Screen Display RepRap Smart Controller Panel Similar 12864 LCD for Ender 3 SKR V1.3 MKS Gen Control Board (TFT 24 for Ender 3)

Product Description
TFT24 Touch Screen Youtube Video:
https://www.youtube.com/watch?v=TeRSGmcd8A8#action=share

Parameters
Appearance size: 105*46mm
Microprocessor: STM32F105RCT6
Input voltage: 5V

Some Important Tips for TFT 24 Touch Screen
1,When using class 12864 screen mode, connect to the motherboard’s EXP1 and EXP2, in which No touch function
2. When using serial-screen mode, connect to TFT or AUX-2 on the motherboard via RS232. Touch function run in this mode
3,The two modes correspond to different firmware, please wire according to the pattern type of flashed firmware
4,There are two choice in the listing, if you select the “TFT 24 For Rnder 3”, we will send the extra cable which can connect with Ender 3 printer directly. Otherwise,it can’t connect without a special designed cable

How to update Firmware
1,Log in the open source website of our company to download: https://github.com/bigtreetech
2,Firmware file name:
BIGTREE_TFT24_12864_(version code).bin
BIGTREE_TFT24_Serial_(version code).bin

First copy the above firmware to SD root directory, and then insert the card into the SD card slot of the board
Next please re-power the board or press the reset key, and wait for about 10 seconds before the update is completed

Packing List
TFT 24 Screen *1 Cable *3(show as picture)

Product Features

  • Using 32bit frequency 72MHz ARM level Cortex-M3 series STM32F105RCT6 Microprocessor, the performance has been greatly improved
  • UART serial screen and 12864 screen two operating modes can be selected with more higher compatibility
  • Serial-screen mode supports both SD card and USB flash drive printing
  • Easy to operate with SD card to upgrade the Firmware

Visit The Website For More Information…

Aokin 3D Printer Controller Kit for Arduino RepRap, RAMPS 1.4 + Mega 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display with Adapter

Product Specs:

(1) Mega 2560 R3
(2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 Specification£ºVDSS:60V ID:55A New MOSFET IC model: HM60N06 Specification£ºVDSS:60V ID:60A HM60N06 current up to 60A£¬More safety

Package List:

(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) Cable x 2
(7) USB Cable x 1

Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Note:
1. You just need to connect the computer with Mega 2560 via USB download cable when burning firmware.
2.The chip and circuit may be burnt when the power and motor driver board reversed, so please confirm twice before powering.
3.You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.

Product Features

  • Mega 2560 control board: The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
  • RAMPS 1.4: RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro¡¯s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered isasking for trouble.)

Click Here If You Need More Detailed Info…

Semoic 3D Printer Kit,Ramps 1.4 + Mega 2560 + MK2B Heatbed + Controller I3 Suit 12864

Semoic,a legal trade mark, has been registered. Only those who are authorized are available to sell items under Semoic. Semoic will bring you joyful shopping experience. 3D Printer Kit,Ramps 1.4 + Mega 2560 + MK2B Heatbed + Controller I3 Suit 12864
Mega 2560 control board: core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery.
Microcontroller
ATmega2560 Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16MHz
PCB Heatbed MK2B Dual Power
This is the later version of MK2B, and can use dual power input, so it is better than MK2A.
Dimensions (Outer): 214mm x 214mm
Dimensions (Heat Bed): 200mm x 200mm
Laminate FR4 1.6+/-0.15mm
2 Layer, 35um Copper
Power Input: 12V/24V DC
Copper Plated Holes
colour: blue & red
Material: metal
Package included
1* Mega 2560 R3
1* LCD 12864 Graphic smart display controller
3* Mechanical endstops + cables
1* MK2B Heatbed
1* Thermistor and high temp wire
1* 2M GT2 belts
2* 30cm Cable
1* Smart adapter
1* USB cable
Only the above package content, other products are not included.

Product Features

  • 3D Printer Controller RAMPS 1.4: The RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion.
  • The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
  • LCD 12864 Graphic Smart Display Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display.You can easy connect it to your Ramps board using the “smart adapter” included.After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller.
  • Print your 3D designs without PC, just with a g-code design stored on the SD card.3 pcs of Mechanical End stops: The mechanical endstop uses a lever switch to detect when it is activated. The switch is wired up so that when activated, it pulls the signal to LOW. There is also an LED on the board that will light up when the switch is activated. It uses a standard 4 pin .pitch header and accepts a standard, old-style CD-ROM audio connector cable.
  • 2M GT2 Belts: For 3D Printing applications, GT2 2mm belt system works better than T2.5, T5, it gives better smoothness and accuracy of positioning, resulting in better printing quality. GT2 timing belt system especially suited for linear movement and positioning applications.

Click Here If You Need More Detailed Info…