WOWOONE CNC 3D Printer Kit for Arduino Mega 2560 R3 RAMPS 1.4 Controller LCD 2004 + 6X Limit Switch Endstop 5 A4988 Stepper Driver 3D Printerarduino arduino

CNC Shield Board:
1>PWM Spindle and direction pins
2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
3>2 x End stops for each axis (6 in total)
4>Coolant enable
5>Uses removable A4988 or DRV8825 compatible stepper drivers
6>Compact design
7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
UNO R3 Board for Arduino:
1>MCU: ATmega328
2>USB interface: ATmega16U2
3>Operating voltage: 5V
4>Digital I/O pins: 14 (including 6 with PWM capability)
5>Analog input pins: 6
6>I-I/O pin output current: 40mA max
7>3.3V output current: 150mA max
8>Flash memory: 32kB (0.5kB used by bootloader- included)
9>Static RAM (SRAM): 2kB
10>EEPROM: 1kB
11>Clock speed: 16MHz
LCD 2004 Smart Controller
Easy connect it to your Ramps board using the “smart adapter” included.
After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card.
Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.

Product Features

  • 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module.
  • The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
  • It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors.
  • Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors
  • This shield can make quick work for managing stepper motors in your project

Click Here If You Need More Detailed Info…

KEYESTUDIO Mega 2560 R3 Board for Arduino Projects with USB Cable

Introduction:
keyestudio Mega (core to ATmega2560) is a development board (used with16MHz crystal oscillator ) of microcontroller. There are 54 I/O (input/output ) digital interfaces (of which 15 are PWM outputs), 16 analog inputs and 4 UART (hardwareserial ports). With its bootloader, program can be downloaded directly with USB and you don’t need to use other external programmer. It can be powered directly by USB, or AC-to-DC adapter and battery.

2Design of Power Supply :
There are two choices (direct power supply trough USB or external power supply) for the power supply system of Mega, and they can be Automatic switched.
External power supply can be AC-to-DC adapter or battery.
Lit rang of voltage of this control board is 6V~12V, but if the supplied voltage is greater than 12V, the voltage stabilizing device will be likely overheated and overheat protection and damaging MEGA will be more likely to occur.
So we suggest the power supply should be 6.5~12V in operation and recommended supply is 7.5 or 9V.

Specifications
Microcontroller:ATmega2560
OperatingVoltage:5V
Input Voltage (recommended):7-12V
Digital I/O Pins54 (of which 15 provide PWM output)
Analog Input Pins:16
DC Current per I/O Pin:20 mA
DC Current for 3.3V Pin:50 mA
256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM:4 KB
Clock Speed:16 MHz

Original Packaging Includes
1 x KEYESTUDIO Mega 2560 R3 Board
1 x USB Cable

Product Features

  • PERFECTLY COMPATIBLE with IDE Software: a nice upgrade to the uno r3 which will allow more complex programs and projects to be done
  • RIGHT OUT OF THE Box: uses the official ATmega16u2 IC instead of CH340G, no driver problem
  • EXCELLENT QUALITY: solder is very clean, everything is aligned nicely, all boards are well packed after function,voltage, current testing, protected in a beautiful box
  • FCC and CE CERTIFICATION: this board made from environmentally friendly components and materials, as well as environmentally friendly production technology, it is really safe
  • We also have a one-stop store that provides various of open source hardware raspberry pi and micro bit, you can access this page at https://www.amazon.com/keyestudio

Click Here For More Information

Aokin 3D Printer Controller Kit for Arduino RepRap, RAMPS 1.4 + Mega 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display with Adapter

Product Specs:

(1) Mega 2560 R3
(2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 Specification£ºVDSS:60V ID:55A New MOSFET IC model: HM60N06 Specification£ºVDSS:60V ID:60A HM60N06 current up to 60A£¬More safety

Package List:

(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) Cable x 2
(7) USB Cable x 1

Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Note:
1. You just need to connect the computer with Mega 2560 via USB download cable when burning firmware.
2.The chip and circuit may be burnt when the power and motor driver board reversed, so please confirm twice before powering.
3.You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.

Product Features

  • Mega 2560 control board: The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
  • RAMPS 1.4: RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro¡¯s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered isasking for trouble.)

Click Here If You Need More Detailed Info…

Semoic 3D Printer Kit,Ramps 1.4 + Mega 2560 + MK2B Heatbed + Controller I3 Suit 12864

Semoic,a legal trade mark, has been registered. Only those who are authorized are available to sell items under Semoic. Semoic will bring you joyful shopping experience. 3D Printer Kit,Ramps 1.4 + Mega 2560 + MK2B Heatbed + Controller I3 Suit 12864
Mega 2560 control board: core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery.
Microcontroller
ATmega2560 Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16MHz
PCB Heatbed MK2B Dual Power
This is the later version of MK2B, and can use dual power input, so it is better than MK2A.
Dimensions (Outer): 214mm x 214mm
Dimensions (Heat Bed): 200mm x 200mm
Laminate FR4 1.6+/-0.15mm
2 Layer, 35um Copper
Power Input: 12V/24V DC
Copper Plated Holes
colour: blue & red
Material: metal
Package included
1* Mega 2560 R3
1* LCD 12864 Graphic smart display controller
3* Mechanical endstops + cables
1* MK2B Heatbed
1* Thermistor and high temp wire
1* 2M GT2 belts
2* 30cm Cable
1* Smart adapter
1* USB cable
Only the above package content, other products are not included.

Product Features

  • 3D Printer Controller RAMPS 1.4: The RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion.
  • The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
  • LCD 12864 Graphic Smart Display Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display.You can easy connect it to your Ramps board using the “smart adapter” included.After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller.
  • Print your 3D designs without PC, just with a g-code design stored on the SD card.3 pcs of Mechanical End stops: The mechanical endstop uses a lever switch to detect when it is activated. The switch is wired up so that when activated, it pulls the signal to LOW. There is also an LED on the board that will light up when the switch is activated. It uses a standard 4 pin .pitch header and accepts a standard, old-style CD-ROM audio connector cable.
  • 2M GT2 Belts: For 3D Printing applications, GT2 2mm belt system works better than T2.5, T5, it gives better smoothness and accuracy of positioning, resulting in better printing quality. GT2 timing belt system especially suited for linear movement and positioning applications.

Click Here If You Need More Detailed Info…