Aokin 3D Printer Controller Kit for Arduino RepRap, RAMPS 1.4 + Mega 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display with Adapter

Product Specs:

(1) Mega 2560 R3
(2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 Specification£ºVDSS:60V ID:55A New MOSFET IC model: HM60N06 Specification£ºVDSS:60V ID:60A HM60N06 current up to 60A£¬More safety

Package List:

(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) Cable x 2
(7) USB Cable x 1

Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Note:
1. You just need to connect the computer with Mega 2560 via USB download cable when burning firmware.
2.The chip and circuit may be burnt when the power and motor driver board reversed, so please confirm twice before powering.
3.You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.

Product Features

  • Mega 2560 control board: The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
  • RAMPS 1.4: RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro¡¯s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered isasking for trouble.)

Click Here If You Need More Detailed Info…

MYSWEETY 39PCS 3D Printer CNC Module Kit, Nema 17 Stepper Motor+CNC Shield Board+UNO R3 Board+RAMPS Mechanical Switch Endstop+DRV8825 GRBL Stepper Motor Driver for Arduino Professional 3D Printer Kit

This is a professional sensor kit for UNO R3. New and upgraded, we provides various components or sensor module, with which you will find it easy for you to complete every experiments or learning. All these are packaged in a portable case, easy to carry and storage.

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino.
GRBL 0.9 compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
Support 6pcs ends stop for each axis.
Coolant enable.
Compatible with A4988 or DRV8825 stepper driver.
Runs on 12-36V DC.

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max
current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware).

Nema 17 Stepper motor:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles.
Length of Cable: 70 cm

Package Includes:
1 x CNC Shield Board
1 x UNO R3 Board
1 x 1.5m USB cable for R3 Board
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
5 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
5 x DRV8825 Stepper Motor Driver
5 x Aluminum heatsink w/ 3M tape backing
12x M3 Screws for bracket of stepper motor

Product Features

  • High Quality-Each sensor is made of premium module, so convenient for circuit connection. These components can be used in a wide range of application, simple and the service life is long.
  • NEMA 17 Stepper Motor — Stepper Motor is 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
  • CNC Shield V3.0-CNC shield board is suitable for CH340G Shield 3.0 version for Arduino, and compatible for GRBL 0.9.
  • UNO R3 Board-Professional module board for UNO R3, fit well for Arduino, easy to install. A great assortment set for Uno R3 starters to learn with and do not miss it.
  • 3D printer CNC Kit -Multiple types of modules or components in this set, which will meet your different needs of learning or experiment.

Click Here If You Need More Detailed Info…

WINSINN 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.6 Upgraded Mosfet + 5Pcs DRV8825 Stepper Motor Driver + LCD 12864 for Arduino Reprap


Ramps 1.6 board:

-Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.

DRV8825 Driver:

-Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
-Six different stepping resolutions: full, half, 1/4,1/8,1/16,1/32
-Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate
-Automatic current decay mode detection / selection
-Thermal shutdown circuit, undervoltage lockout, crossover current protection
-Ground short-circuit protection and load short-circuit protection

Mega 2560 R3:

-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limits):6-20V
-Digital I/O Pins:54 (of which 14 provide PWM output)
-Analog Input Pins:16
-DC Current per I/O Pin:40 mA
-DC Current for 3.3V Pin:50 mA
-Flash Memory:256 KB of which 4 KB used by bootloader
-SRAM:8 KB
-EEPROM:4 KB

—————————————————————————————————————

Package include:
►1 x RAMPS 1.6 Board
►1 x Mega 2560 R3 Board
►1 x 12864 LCD Display Controller
►1 x LCD Smart Adapter
►5 x DRV8825 Stepper

———————————————————————————————————————

►Note:
►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • ✔️DRV8825 driver board widely used in 3D printers and small CNC machines. It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance. It suitable for driving below 8.2V ~ 45V 2.5A stepper motor, And had Six different stepping resolutions: full, half, 1/4 ,1/8, 1/16, 1/32.
  • ✔️12864 LCD: The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using “smart adapter” included. This panel connect your RAMPS 1.6, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller.
  • ✔️This kit includes a complete set of the most common and useful components that can be used by all tech-savvy people out there to build their own printer controller. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • ✔️Product Warranty: WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
  • ✔️Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be samller than 200W.

Click Here If You Need More Detailed Info…

SainSmart 6-Axis Desktop Robotic Arm & Grippers, Assembled for Arduino UNO MEGA2560

Overview:

This 6 axis Desktop Robotic arm includes SainSmart’s professional after sales service, with the manual and necessary documentation
included in our wiki site. SainSmart’s Robot Arms are perfect for hobby projects to higher level education and robotics research.
CNC machined PVC skeleton provides a lightweight and reliable structure suitable for most smaller projects needing a robotic arm.
This unit utilizes MG996 55g metal gear servos (4pcs) and active joint bearing connections, providing a flexible and responsive robotic arm.
Basic robotic arm programming and mechanics is often used as the “stepping stone” to dive into the industrial robotics and automation
industry, which can fit a wide range of project needs.

MG996 55g Servo Specifications:

Size: 40.7*19.7*42.9mm
Working torque: 9.4-13kg/cm
Respond rotation speed: 53-62R/M
Working temperature: -30~+60°C
Dead zone: 5us
Plug: JR, Tutaba
Rotation angle: 180 degree
Analog servo
Working current: 100mA
Working voltage: 5-7.2V
Metal gear, coreless motor, two ball bearing
Operation speed: 0.17s/60 degree(4.8V); 0.14S/60 degree(6.0V)

SG90 9G servo Specifications:

Size: 23*12.2*29mm
Weight: 9g
Working torque: 1.6kg/cm
Respond rotation speed: 0.12-0.13s/60 degree
Working temperature: -30~+60 C
Dead zone: 5ms
Plug: JR, Tutaba
Rotation angle: 180 degree
Analog servo
Working current: 100mA
Working voltage: 3.5-6V
Metal gear

Package List:

4x MG996R servo
2x SG90 servo
1x Structural Frame Bearings
All necessary screws

Manual: http://wiki.sainsmart.com/index.php/DIY_6-Axis_Servos_Control_Palletizing_Robot_Arm_Model_for_Arduino_UNO_MEGA2560

NOTE: Mega Board is not Included.

Product Features

  • Production Quality: Structure consists of different thickness of CNC machined PVC plates, making it a durable and quality product guaranteed. The main joints utilize metal gear servos (MG966R and SG90), ensuring a reliable and smooth operation.
  • Motion Flexibility: Quality servos, precision structure, and 6 axis design allow an immense range of motion and flexibility within its reasonable limits.
  • Programmable: Servos are completely programmable using any microcontroller and code. We provide a lot of source code on our wiki webpage( SainSmart Wiki )for the Arduino Mega, making this unit suitable for beginners!
  • Simple Setup: All the parts are fully assembled, allowing for immediate programming and use.
  • Stem Education: Simulate this real palletizing robot arm and learn about the basic construction of a real robot arm. A fun STEM educational experience in mechanical engineering and electronics.

Visit The Website For More Information…