Heat Bed Power Module, 2-Pack 3D Printer Hot Bed Power Expansion Board/Heatbed Power Module/MOS Tube High Current Load Module with Cables

Heated Bed Power Module Features:
Helps 3D printer equipped with the controller board (capable of max 15A) become more powerful.
With this add-on module to board lead the maximum current up to 25A.
If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this module is recommended, else it may cause excessive current during times which may burn the connectors on the controller board.
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this)

Specifications:
Color: Black
Max Current: 25A (Enhance heat dissipation)

Note:
1.This module under the premise of normal cooling, found at I (Max) = 25A stable work situation, the process of using the current not exceed 25A.
2.Please double-confirm the wire you connect is right when installing this MOSFET Board, if you have any issue please contact us firstly, thanks!

Packing Included:
2 x Heated Bed Power Expansion Module (motherboard is not included)
2 x Connection cable for input signal

Product Features

  • This high power module is a general add-on heated bed power expansion module for 3D printer. Effective to resolve the hot bed power is too large and the load current problems. It compatible with Anet A8 and most 3d printers.
  • The heat bed power module can be used in both Chitu motherboard and other open 3D printer motherboards.
  • With this add-on module to your controller board, you can lead the maximum current up to 25A. If you need anything greater or equal to 15A this module is a must!
  • When using heated bed 3D printer for 12V power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning.
  • Note: Under the premise of normal cooling, it works stably under I(Max)=25A, the current must NOT exceed 25A while in the work process.

Click Here For More Information

Haitronic 120pcs 20cm length Jumper Wires/dupont cable Multicolored(10 color) 40pin M to F, 40pin M to M, 40pin F to F for Breadboard/Arduino based/DIY/raspberry Pi 2 3/Robot Ribbon Cables Ki

We Haitronic are original Factory with traditonal wholesale distributors on various jumper wires, arduino wire connectors.

New released on Amazon only on Oct 7th 2016, although there are few reviews till now, we actually sold few hundreds of a month.

This 3 in 1 set Jumper wire is Durability Tested ULTRA USERFUL!

After you tear apart into individual cable, in total 120pcs cable, 10 different color do to multiful DIY electronic connection. Each axis has 20cm length, with 10 colors option(each color has 12 roots), and 3 various F2F, F2M, M2M pin, very convenient for Arduino/breadboard or other DIY connection, Maker experiment, engineers LAB testing, as well as can be soldering as you wish.

——————————————————–

Features:

Ø Color: 10 options as shown in the pictures.

Ø Material: high-grade copper core.

Ø Each cable length: 20cm / 8-inch.

Ø 3 pieces of the 40pin breadboard jumper wires in one set together.

Ø Including one 40-pin male to female jumper wires, one 40-pin male to male jumper wires, one 40-pin female to female jumper wires.

Ø The male ends meant for insertion into standard 0.1 quot;(2.54mm) female sockets and the female ends are meant for insertion into standard 0.1 quot;(2.54mm) male headers.

Ø The cables can be separated into single root as you request to do multiple connection.

Ø Portable design, easy and safe to use.

——————————————————–

What’s in Package:

* 1 x 20cm 40-pin Male to Female prototyping Jumper Wires Ribbon Cable

* 1 x 20cm 40-pin Male to Male prototyping Jumper Wires Ribbon Cable

* 1 x20cm 40-pin Female to Female prototype Jumper Wires Ribbon Cable

ØYour REVIEW is ULTRA PRECIOUS! we sincerely invite you share your review for this Multicolored BB Jumper Wires, MANY THANKS!

Product Features

  • 10 different colors, 120units copper cable in total, for making prototypes with arduino boards, stepper motor 3D printer etc, The combinations provide a jumper for whatever you need. Just peel off
  • Factory directly, 10 tiny copper wires inside of single jumper wire: high-level copper wire inside, durable for conductive connection.
  • 0.127mm, 36 AWG/ single root, 20cm(7.87inch)/axis; Standard 2.54mm headers and sockets.
  • Can be detached into120 single axis: 40 male-male, 40 male-female, 40 female-female.
  • Computers and smart phone maintainance, Various prototyping, such as Arduino/Maker/3D printer control board, DIY experiment needs frequently, If the terminals does not damaged it can be reused, if dam

Visit The Website For More Information…

SIMPZIA Heat Bed Power Module General Add-on Hot Bed Power Module Expansion Board High Current Load Module Mos Tube Hotend Replacement with Cables for 3D Printer – 2 Pack

Heated Bed Power Module Features:
Based on powerful MOSFET HA210NO6
Dimensions: 70 x 45mm/ approx 2.76 x 1.77″
Distance between holes: 62.8 x 37.8mm/ approx 2.47 x 1.49″
Supply/Operating Voltage: 12V-50V (12-24VDC recommended)
Max Current: 25A (Enhance heat dissipation) safe for prolonged times. ensure active cooling of the heatsink.
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this)

Package Includes:
1 x Heated Bed Power Module.
1 x Connection cable for input signal
2 x Power cable

Note:
This module under the premise of normal cooling, it work stable under (Max) = 25A, the process of using the current not exceed 25A.

Product Features

  • APPLICATION: This high power module is a general add-on heated bed power expansion module for 3D printer. It can work with the Anet A8.
  • UNIQUE DESIGN: With unique snowflake heatsink design, it has a great cooling effect. The heat bed power module can be used in both Lerdge motherboard and other 3D printer motherboards.
  • 25A MAXIMUM CURRENT: This high power module helps your 3D printer equipped with the Lerdge controller board become even more powerful. The module can solve the current load problem when the heated bed power is too large. With this add-on module to board lead the maximum current up to 25A.
  • GOOD PROTECTION: When using heated bed 3D printer for 12V power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning.
  • PACKAGE INCLUDES: 2 x Heated bed power module (motherboard is not included) and 2 x Connection cable for input signal. BONUS: 4 x Power cables.

Detailed Information available on our Homepage…

Mini Heat Bed Module, FYSETC Hot Bed Power Expansion Board High Current Load Module MOS Tube Hot Bed Mos with Cables for 3D Printer Parts – 2 Pack

Feature
1.Size (LxHxW): 6 x 2.3 x 3.1 cm/ 2.5″ x 0.9″ x 1.2″
Voltage: 12V-50V (12-24VDC recommended)
2. Connect Power to power source, please note the anode and cathode.
3. Connect Hotbed to heated wire, please note the anode and cathode.
4. Connect digital control signal to Gnd, D8.
5. Connect the control signal of Ramps1.4 or MKS MOSFET to -Bed+
6. Choose one signal group to connect.
7. If you don’t know how to install, please contact us or find the related link in youtube, thanks

Please kindly note:
Pay attention to polarity
Only can choose 3 or 4 signal group

Package included:
2 x 3d printer heated bed power module;
2 x connection cable for input signal

Product Features

  • Function and Use: control hot bed, print head heating, compact appearance, compact design, more powerful heat dissipation, to solve the problem of excessive heat bed power, current load problem;
  • Extra large heat sink, the maximum current can be up to 30A or more, can use digital signal of 5-24v to control;
  • This module under normal cooling, measured I (Max) = 30A can Stable long-term work during use, so we suggest the current should not exceed 30A.
  • Connect the control signal of Ramps1.4 or MKS Mosfet to bed, can use hot bed output signal of Ramp1.4 and MKS series to control;
  • After-sale Guarantee: Each one will be done functional test before shipment, so anyone receives a defective one please don’t feel hesitate to email us before leave negative review and feedback, we will give you support within 24 hours.

Visit The Website For More Information…