Complete Ultimate Starter Kit for Arduino with Mega2560, LCD, Servo Motor, Sensors,Breadboard and Jumper Cable

Product List
1xMEGA 2560 Board(Arduino MEGA 2560 R3)
1xMEGA 2560 Development Expansion Board
1xMini Breadboard
1xADXL345 Acceleration Sensor
1xUltrasonic Distance Sensor
1xIR Receiver HX1838
1xRemote Controller
1xPS2 Joystick Module
1xRelay
1xStepper Motor
1xULN2003 Stepper Motor Driver Module
1xDHT-11Temperature & Humidity Sensor
1xLED Bar Graph
1xActive Buzzer
1xPassive Buzzer
1xPIR Movement Sensor
1xServo
2xAnalog Temperature Sensor(Thermistor)
1xBreadboard Power Supply Module
1×4*4 Matrix Keyboard
1xDC Motor
1xL9110 DC Motor Driver
1xLCD1602
1xDot-matrix Display
1×7-segment Display
1×4-bit 7-segment Display
1xNE555 Timer
2x74HC595
2xLight Sensor (Photoresistor)
2xTilt Switch
2xSwitch
1xRGB LED
8xRed LED
4xGreen LED
4xYellow LED
4xBlue LED
16xResistor(220O)
10xResistor(1kO)
10xResistor(10kO)
2xPotentiometer(10KO)
5xCapacitor(104)
4xCapacitor(10uF)
4xButton(large)
8xButton(small)
1xButton Cap(red)
1xButton Cap(white)
2xButton Cap(blue)
4xNPN Transistor(8050)
4xPNP Transistor(8550)
4x1N4148 Diode
4x1N4001 Diode
1x9V Battery Clip
1xBreadboard
1xUSB Cable
40xMale to Male Jumper Wires
20xMale to Female Jumper Wires
20xFemale to Female Jumper Wires
1xHeader(40pin)
1x Band Resistor Card
1x Project Box
About Arduino:
Lesson 1 Blinking LED
Lesson 2 Active Buzzer
Lesson 3 Controlling an LED with a button
Lesson 4 Controlling Relay
Lesson 5 Serial Port
Lesson 6 LED Flowing Lights
Lesson 7 LED bar graph display
Lesson 8 Breathing LED
Lesson 9 Controlling a RGB LED by PWM
Lesson 10 Play the Music
Lesson 11 LCD1602 display
Lesson 12 A Simple Voltmeter
Lesson 13 7-segment display
and so on

Product Features

  • This is an upgrade complete Arduino starter kit designed for beginners and electronic hobbyists.
  • With more than 33 projects, it is esay and convenient for you to learn Arduino and programming
  • The starter kit will make a great gift for any to-be engineers, or anyone looking to get a jump start in the world of microcontrollers and programming. Hundreds of tutorials and guides can be found online and the range of projects that can be created with an Arduino is vast
  • This kit comes with everything that the average beginner Arduino project requires, plus more, 50 kinds of different electronic components, more than 180 components, such as Arduino Mega2560, 1602 LCD display are included. It has enough variety to learn most of what can be done with the arduino and electronics in general
  • The kit is a great help for you learning electronics! Lots of little bits to start doing Arduino things

Click Here If You Need More Detailed Info…

Wangdd22 3D Printer Kit 14pcs/lot Cables Complete Wiring Cables Set For RAMPS 1.4 Endstops Thermistors Motor Dupont Cable

Description:
Use these cables enjoy your all of your electronic projects,Such as 3D printers, Arduino motherboards, modules and so on.

Package includes:
3pcs 70cm 2pin F-F Wires
6pcs 70cm 3pin F-F Wires
5pcs 70cm 4pin F-F Wires

Product Features

  • Cable Length:70cm.
  • Cable Attributes: Female to Female.
  • Product Color: Red, Black, Green, Blue.
  • 1 Set=3pcs 2pin+5pcs 4pin+6pcs 3pin cable
  • Product uses: Such as 3D printers, Arduino motherboards, modules and so on

Click Here If You Need More Detailed Info…

[Sintron] NEW Ultimate 3D Printer Full Complete Kit TW-101 2017 Upgrade Pro & Easy 3D Printer Reprap Prusa i3 + MK8 Extruder, Stepper Motor and LCD Controller

The operating principle of 3D printer is to establish a 3D model by your computer, and use slicing software system to do the slicing work for the 3D model then save to the SD card for ready to print. Made of high quality acrylic material + Steel rod (threaded & smooth), this 3D printer has a simple structure, light and portable, beautiful and trendy.

Sintoron TW-101 3D Printer Assembly Guide Video, please click this link : https://www.youtube.com/watch?v=Cjv6HPep_dU

TW-101 has complete pdf instruction as well as Exploded view video–> hardware parts
TW-101 has open source preconfigured Marlin configuration –> firmware part
We also provide software for TW-101: such as Pronterface, Slic3r. and most importantly, we can provide the configuration file of slic3r, which we spent so much time to set it up. with this, your printing would be beautiful! –> software part

Quick & Easy assembling, all you need are just one wrench + screw driver. and they are included! we have classified the parts, screws, nuts for you. this would save you lots of time!

Actually we have own this products for over one year, but we just started to sell it now. because we hope to went through all the details, and make sure all the components we selected are really useful, so customer can save time on worrying if it’s the hardware problem and focus on project only.

Therefore, if you meet any problems (I am sure you will meet dozens of problems and questions during the building process, and it’s normal), you can always contact us for technical support, because almost all the problems you will meet, we already met before, you are not just buying this product, you also get our experienced support for you. if there’s some one you can ask, you will save a lot of time.

Package list and TW101 Specifications : please check the main picture for list.

Product Features

  • (1) We don’t adapt wade extruder, we upgrade the J-head to all metal Sintron MK8 extruder (not all the MK8 extruders are the same). If you use wade extruder etc, every time when you change the filament, you have to take them apart and calibrate it all again. it takes hours sometimes. it takes you only within 1 minute to change the filament. Sintron MK8 extruder’s special design also ensure you a pleasant & smoth printing.
  • (2) We use SINTRON well-designed standard MK8 extruder, high quality stepper motor and direct drive extrusion wheel, more accurate, quick heating and fluent injection, we have made necessary design to prevent “jammed” problem. Exclusive Anti-Backlash design for Z axis , this makes the movement very quiet and stable. only Sintron got this design in the Market now! Sintron TW-101 uses 304 stainless T8 Lead Screw with Thread pitch 2mm. this makes TW-101 more accurate in printing.
  • (3) Wiring has never been as easier as TW-101. you are not a expert of electronics? Never Mind! we have mistake-proof plugs. this is also one of our special design. as long as you can read and check the color, you can do it! Further more, we have made wires with corresponding suitable length for each plug(others don’t). so it would look tight and clean! no extra mess.
  • (4) Energy Saver! TW-101 consumes only 1/3 energy of ordinary 3d printer, TW-101 adapts special tape. so you don’t need to heat the bed, therefore no worries about fire accident. but on the other hand, TW-101 by default won’t suit for ABS(toxic) printing, PLA(non-toxic) and others are preferred. it’s also a trend to use only PLA as it’s enviormental friendly and no harm for human body.
  • (5) Sintron TW-101 provide good Full tech support for the machine, unlike other sellers, just sell and know nothing about the product. we provide support for hardware, firmware & software if you would like to discuss with us! this would make sure you learn a lot from it too!

Click Here If You Need More Detailed Info…

LANDZO Prusa i3 Complete 3D Printer Kit

Product introduction
The operating principle of 3D printer is to establish a 3D model by your computer, and use slicing software system to do the slicing work for the 3D model then save to the SD card for ready to print. Made of high quality acrylic material + Steel rod (threaded & smooth), this 3D printer has a simple structure, light and portable, beautiful and trendy.
The Glass Print Bed plate is 214mm X 202X 230mm
1. High transparency.
2. Good adhesion when heated, easy to separate plastic parts after cooling.
3. Eliminate the need to replace the special plastic film troubles, there is no special plastic film with the old sticky weakened problem.
Model – Complete DIY Kit (Unassembled).
Less parts. Easy Assembling. High performance.

Technical Specifications
Color: Black
Build Size:214*202*230mm
Machine Size: 497*516*443mm
Layer Thickness: 0.05-0.3mm
Model Material: 1.75mm PLA/ABS/PETG/TPU/PVA/WOOD
Voltage: 100-240V (Automatic voltage regulation)
Power:150w
Nozzle Size: 0.5mm
Extruder Temperature: Up to 260℃
Best Printing Temperature: ≥25℃
3D Files Format: STL OBJ
Technology: Fused Deposition Modeling(FDM)
Workstation Compatibility: Linux and Windows
Connection: SD card, USB line, U-disk
Software: software/Cura/Simplify3D/Repetier-host/Slic3r
Packing Size:510*295*220mm
N.W.: 6.5kg G.W.: 8kg

if you meet any problems (I am sure you will meet dozens of problems and questions during the building process, and it’s normal), you can always contact us for technical support, you are not just buying this product, you also get our experienced support for you.

Product Features

  • Easy to use software for simple customization of 3D models, Made of high quality acrylic material + Steel rod
  • Onboard software permits standalone operation when needed
  • Limit switches more accurate positioning ,stronger and more stable performance
  • High-definition touch screen,professional hot end design ,precise mounting palte design,Separate filament holder
  • High quality after-sales service and technical support

Click Here If You Need More Detailed Info…