HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

For Arduino Professional 3D printer CNC Kit,Longruner GRBL CNC Shield +UNO R3 Board+RAMPS 1.4 Mechanical Switch Endstop+DRV8825 A4988 GRBL Stepper Motor Driver with heat sink+Nema 17 Stepper Motor

CNC Shield Board: Latest CNC Shield Version 3.0 for arduino. GRBL 0.9 compatible. 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). 2 x End stops for each axis (6 in total). Coolant enable. Compatible with A4988 or DRV8825 stepper driver. Runs on 12-36V DC. DRV8825 Stepper Motor Driver: Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware). Nema 17 Stepper motor Specification: Model No.:17HD48002H-22B Step Angle: 1.8 deg Holding Torque: 59Ncm(84 oz.in) Rated Current/phase: 1.7A Frame Size: 41 x 41mm Body Length: 47mm Shaft Diameter: 5mm Shaft Length: 22mm Weight: 380g Mechanical Endstop Connection Description: Red line connect VCC (ramps of +) black wire connect the GND (ramps of -) Green Line connect SIGNAL (ramps in s) Tips: Under normal circumstances, the system must be configured to at least three mechanical switches. Advantage: Easy to install, the more common used styles. Length of Cable: 70 cm Great Package Includes: 1 x CNC Shield Board 1 x Longruner UNO R3 Board 1 x 1.5m USB cable for R3 Board 3 x Nema 17 stepper motor 1.7 A (with bracket and screw) 3 x Nema 17 Stepper Motor Mounting Bracket 3 x Mechanical Switch Endstop 3 x 3Pin 70cm Cable 4 x DRV8825 Stepper Motor Driver 4 x Aluminum heatsink w/ 3M tape backing 12x M3 Screws for bracket of stepper motor

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino.
  • Longruner UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable.
  • 4pcs DRV8825 Stepper Motor Driver with Heat Sinks.
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable.

Click Here If You Need More Detailed Info…

Quimat Arduino CNC Shield Contoller Kits for 3D Printer,CNC Shield V3.0 + UNO R3 Board + Nema 17 Stepper Motor + A4988 Stepper Motor Driver + Heat Sinks,Perfectly Compatible with GRBL

CNC Shield V3.0 features: Latest Arduino CNC Shield Version 3.0. GRBL 0.8c compatible.(Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support(X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis(6 in total), Spindle enable and direction Coolant enable Stepper drivers Uses removable Pololu A4988 compatible stepper drivers. Jumpers to set the Micro-Stepping for the stepper drivers. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Stepping Motor The most popular Nema 17 model with 1.8 deg. step angle (200 steps/revolution) 0.4A rated current/phase, allowing for a holding torque of 26Ncm(36.8oz.in) Connection:Black(A+), Green(A-), Red(B+), Blue(B-) Stepping Motor Specification: * Cable length: 11.8 inches * Phase Resistance: 30ohms * Inductance: 37mH+/-20%(1KHz) * Frame Size: 42 x 42mm * Body Length: 34mm * Shaft Diameter: 5mm * Front Shaft Length: 20mm * D-cut Length: 15mm * Number of Leads: 4 * Lead Length: 300mm * Weight: 230g Kit list: 1x CNC Shield V3.0 1x Keyestudio UNO R3 board 4x A4988 driver 1x USB cable 1x Nema 17 stepping motor

Product Features

  • CNC Shield V3.0 Features – Latest Version 3.0, GRBL 0.8c compatible, 4 Axis supported and 2 end stops for each axis.
  • Compact design – Stepper motors can be connected with 4 pin molex connectors or soldered in place.
  • Stepper Drivers – Uses removable Pololu A4988 compatible stepper drivers, jumpers to set the Micro-Stepping for the stepper drivers
  • Stepping Motor Included – Nema 17 model, holding torque of 26Ncm(36.8oz.in), 12V/0.4A and 1.8 deg.step angle(200 steps/rev)
  • Technical support – Our technical support team is on standby to provide solutions to your questions, please feel free to contact us.

Click Here If You Need More Detailed Info…

Elegoo 5 sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

Elegoo Inc. is a professional manufacturer and exporter that is concerned with the design, development production and marketing of arduino, 3d printers, raspberry pi and STM32.
Our Dream is to make the best price and best quality produce for customers.
So we would like to receive your valuable suggestions for our products and we can improve them for you.

Features:
– A, B, C, D four-phase LED indicates the status of the stepper motor work.
– Stepper motor with a standard interface, when used directly pluggable.
– 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board,With convenient use, direct docking
– Rated Voltage: DC5V 4-phase
– Insulation Resistance: >10MΩ (500V)
– Dielectric Strength: 600V AC / 1mA / 1s
– Step angle: 5.625 x 1/64
– DC Resistance: 200Ω±7% (25C)
– Reduction ratio: 1/64
– Insulation Grade: A
– No-load Pull in Frequency: >600Hz
– No-load Pull out Frequency: >1000Hz
– Pull in Torque: >34.3mN.m(120Hz)
– Detent Torque: >34.3mN.m
– Temperature Rise: 《40K(120Hz)

Package including:
5 set Uln2003 Stepper Motor + Driver Board
10pcs female to male cable ( as a gift)

Product Features

  • Stepper motor with a standard interface, when used directly pluggable.
  • A, B, C, D four-phase LED indicates the status of the stepper motor work.
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board,With convenient use, direct docking
  • Drive Module Board Size(in): 1.37*1.18*0.6 ; Stepper Motor diameter: 1.06(in) ; Stepper Motor lines: 9.45(in)
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board (with a little gift)

Detailed Information available on our Homepage…