Anycubic Upgraded Full Metal i3 Mega 3D Printer with Ultrabase Heatbed and 3.5 Inch Touch Screen

Anycubic Upgraded Full Metal i3 Mega 3D Printer –UltraBase Version

Quality Warranty:
Anycubic takes care of all parts of unartificial quality-related issues with a replacement for 3 months after the purchase date,and provide lifetime technical support.
Technical Support Email Address:
[email protected]
[email protected]

Specificaiton:
Printing Technology: FDM (Fused Deposition Modeling)
Layer Resolution: 0.05-0.3 mm
Positioning Accuracy: X/Y 0.01mm Z 0.002mm
Print Speed: 20~100mm/s (Recommended Speed 60% )
Travel Speed: 100mm/s
Nozzle Diameter: 0.4 mm
Support Print Materials: PLA, ABS, HIPS, WOOD
Build Dimensions : 210 x 210 x 205mm
Operational Print Bed Temperature: 110oC
Operational Extruder Temperature: max 260oC
Ambient Operating Temperature: 8oC – 40oC
Leveling Type: Manual Leveling
Input Formats: .STL, OBJ, .DAE, .AMF
Slicer Software: Cura
Cura Output Formats: G-Code
Connectivity: SD Card & USB support
Input Rating: 100-240V AC, 50/60Hz, 1.5A
Printer Dimensions: 405 x 410 x 453mm
Package Weight: 15kg

Youtube Video:
https://www.youtube.com/watch?v=seIY2dSLJ3Y

Certifications:
CE, FCC, RoHS ,EN

Package List:
1x I3 Mega
1x 8G SD Card
1x User Manual
1x PLA filament ( 1Kg )
1x Tool Set

Product Features

  • Large Build Volume :210 x 210 x 205mm.
  • Plug and Play with User Friendly Screen :Complete the assembling with 8 screws ,then start to play through a 3.5-inch TFT touch screen.
  • ANYCUBIC UltraBase: ANYCUBIC patented heatbed,super adhesion,smoothy lattice bottom surface. Easier to take off model by hands, so you won’t need masking tape and glue stickers any more.
  • Filament Detection: Automatic printing pause when filament runs out, resume after filament re-load with just one click.
  • Anycubic Advantage:We take care of all parts of unartificial quality-related issues with a replacement for 3 months after the purchase date,and provide lifetime technical support.

Click Here For More Information

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB

-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
– Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can’t be sure to match all of stype of 12864LCD and 2004LCD )
– Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.

Specification:

Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g

Package Included:

1* MKS Gen V1.4 Control Board

Product Features

  • Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.
  • Replace the motor drive, drive and support 4988 8825 drive.
  • The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
  • Using high-quality MOSFET, and better heat dissipation.
  • Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.

Visit The Website For More Information…

Arduino 3D Printer Controller Kit – Mega 2560 Board, 3D Printer Controller RAMPS 1.4 Board, 5 Steppers, SD Card Slot, 12V, 180W

Build your own 3D printer controller kit and print all your 3D designs via G-codes on your SD card without the need of a PC.

Manufacturer SpecificationsManufacturer_Specifications
GeneralgeneralMax power supply for these ramps: 12VMax watts for these ramps: 180WMax watts for the hotbed: 100WMax temperature for the hotbed: 50 Degree CelsiusThis kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD.It can control up to 5 stepper motors with 1/16 stepping precision and interface with a hotend, a heatbed, a fan (or a second hotend), a LCD controller, a 12V (or 24V with appropriate modification) power supply, up to three thermistors, and up to six end stoppers.RAMPS 1.4 shield is a popular control board for RepRap Prusa i3 3D compatible printer.A4988 Stepper Motor Driver is built-in translator for easy operationLCD 12864 with Controller contains an SD-Card reader, a rotary encoder and a 128 Character x 64 Line LCD display.
Dimensionsdimension_infoArduino Board Dimensions: 115x 50x 9mm (L x W x D)Arduino Board Weight: 35g3D Printer Controller Board Dimensions: 105x 60x 20mm (L x W x D)3D Printer Controller Board Weight: 68gWeight/dimension is for the main item of this boxed product, to help you compare product sizes before buying: please do not base your shipping calculations on this price – shipping prices depend on your cart contents, shipping destination, and shipping method: please use the checkout to select options and preview shipping price for your total order.
Product NotesProduct_NotesDo not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touch

Click Here If You Need More Detailed Info…