HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB

-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
– Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can’t be sure to match all of stype of 12864LCD and 2004LCD )
– Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.

Specification´╝Ü

Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g

Package Included:

1* MKS Gen V1.4 Control Board

Product Features

  • Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.
  • Replace the motor drive, drive and support 4988 8825 drive.
  • The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
  • Using high-quality MOSFET, and better heat dissipation.
  • Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.

Visit The Website For More Information…

TriGorilla MKS BASE V1.0 3D Printer Control Motherboard Compatible RepRap Ramps1.4 With USB Cable

Specification:
Can accept 24 v input, under the same system power can reduce the current hot bed to 1/4, effectively solve the problem of hot bed MOS tube heating
The firmware can use open source firmware Marlin, configuration are exactly the same with ramps1.4 , can be directly replace ramps1.4 also
Can be connected directly to Ramps1.4, 2004 LCD control board and the LCD board (12864)
Package Contents:
1 x MKS-BASE V1.0
1 x USB cable

Product Features

  • It gather all function on one board, which solved the Ramps1.4 combination interface problem, which easily out of order
  • Using 4982 as a motor drive, the SOP package, the effect of heat dispelling is better
  • Circuit board uses the high quality of 4 layer board,optimize heat dissipation;Ramp Is 2 layer board
  • Using special power supply chip, support the 12v-24v power input, solve the problem of Ramps voltage conversion of chip fever

Detailed Information available on our Homepage…

Gowoops 3D Printer Motherboard MKS MINI V1.2 RepRap + 2.8 Inch Full Color Touch Screen LCD MKS TFT28 V1.2

MKS MINI V1.2 Board User Manual: http://osoyoo.com/2016/09/21/mks-mini-v1-2-3d-printer-board-circuit-connection-graph-and-firmware-installation-guide/

MKS-TFT28 Touch Screen User Manual: http://osoyoo.com/2016/07/25/mks-tft-2-8-touch-screen/

Caution:
1) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) .
2) Always double check power wire is properly installed. If you do not follow above move, you can damage the control board and your 3D printer.

MKS MINI V1.2 printing integrated mainboard:

MKS MINI is a feature all-in-one electronics solution for Reprap and other CNC devices.
It features an onboard ATmega2560.
It’s four motor outputs are powered by DRV8825 stepper drivers.
The board can use the same firmware as Ramps1.4.
The mounting hole locations is the same as Arduino Mega2560.
The power supply with 7805, more stable and reliable than the 1117, but only supports 12V.USB to serial modules is 16U2, the same as Arduino Mega2560.Without hot bed heating output, but has bed thermal interface and bed control signal interface.

MKS-MINI is suitable for One-Extruder and no bed printing.

LCD Full Color Touch Screen MKS TFT28 V1.2
Set the Boot
1) Must: After the first boot into -> Settings -> connection, select the firmware used by the baud rate, it can be used.
2) You must: Go to -> Settings -> type, select the printer type, only Delta and the other two options.
3) Optional: You can enter -> Settings -> touch screen calibration, improve the accuracy of the touch screen.

Package Included:
1 x 2.8 Inch Full Color Touch Screen MKS TFT28 V1.1 For 3D Printer
1x MKS MINI V1.2 Board

Product Features

  • MKS MINI V1.2 Board: Arduino MEGA compatible Atmega2560 processors are compatible with all RAMPS class firmware. Easy DISPLAY + SD-CARD connector, RepRapDiscount. SmartController compatible pin header on board. Firmware can use the same configuration as ramps1.4.
  • MKS MINI V1.2 Board: 2x temperature ADC connectors for thermistors, up to 4 motor driver with DRV8825. 2x PWM capable power mosfet outputs with voltage selector for MainPower.(Extruder0,Fans). 6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax. 4 layers PCB, optimize heat dissipation. Recoverable fuse for short-circuit protection.
  • MKS-TFT28 is an independent color touch product suitable for the use of open source 3D printers, support U disk and SD card. The main control program without need modification, plug and play, support Marlin, Repetier, Smoothieware firmware.
  • MKS-TFT28 support power failure renew,power failure preservation. The main control program without need modification, plug and pla. Can increase the custom function button. Provide continuous software upgrade, upgrade method is simple.
  • MKS-TFT28 can be used on Ramps1.4 and MKS Base , MKS Gen , MKS Mini and a series of motherboard. Boot logo and all buttons, such as interface can be designed by ourselves.

Visit The Website For More Information…