BIQU 3D Printer Part SKR Mini V1.1 32bit Control Board Marlin 2.0 Open Source Compatible with Ramps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers (DC Connector)

SKR Motherboard Parameters:
Appearance size: 90*70mm
Mounting size: 80*60mm
Microprocessor: ARM Cortex-M3 CPU
Input voltage: DC12V-DC24V 5A-12A
Motor driver: support TMC2208, TMC2130, ST820, LV8729, DRV8825, A4988
Motor drive interface: X, Y, Z, E0, Four(Serial Dual Z-axis), Up to 256 subdivisions
Display: 2.8 “TFT, 3.5” TFT
Temperature Sensor Interface:TH0、TB, two 100K NTC thermistor

Notice:
When the SKR motherboard is electricity , the red light D2 in the lower right corner will light up, indicating that the power supply is normal. The middle of the Board DC SEL is the power selection end
1, when using USB to power the motherboard, short circuit cap should be used to connect +5V and USB Pins
2, when using 12v-24v power supply, short circuit cap shall be used to connect +5V and INT pins

Attention: Can be connected [12v-24v power], [USB] at the same time , the printing process must be connected with a short circuit cap +5V And INT
3,The Board 5V SEL must be connected to INT and +5V two pins before it going to print 4,It must be connected with an external hot bed MOS Extension Module if you need to use with Heatbed, it is very significant that Motherboard can not connect with heat bed directly.

How to use
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1,The driver can be obtained from our open-source website: https://github.com/bigtreetech, named by “mapleDrv” file
2. After installing the driver, connect the computer and SKR motherboard with USB cable
If you need more information about this Board please contact us

Product Features

  • Using 32bit frequency 72MHz ARM Cortex-M3 series STM32F103RCT6 main Microprocessor, the performance has been greatly improved
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • SKR Mini V1.1 Board adopt “Gold Finish” process which capability is more stable and better heat dissipation
  • Support 2.8 and 3.5 Inch Touch Screen,2004LCD (but don’t Support 12864 LCD)

Visit The Website For More Information…

BIQU 3D Printer Part SKR V1.3 32bit Control Board Smoothieboard&Marlin Open Source Compatible with Ramps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers

Product Description
BIGTREETECH SKR V1.3 motherboard is R&D by Shen Zhen Big Tree Technology CO.,LTD. .The BIGTREETECH SKR V1.3 motherboard not only with a high cost-effective but especially suitable for small and medium-sized 3D printers

How to Work
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1. Smoothieware-usb-driver-v1.1 driver installation (Windows systems only) The driver can be obtained from our open-source network
Https://www.dropbox.com/s/ighnj7oa2l0bm5g/smoothieware-usb-driver-v1.1.exe?dl= 0
2. After installing the driver, connect the computer and SKR motherboard with USB cable
Note: When using smoothieware open-source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! !
3. If you are using Marlin2.0 firmware, follow the tutorial to install:
Tutorial:https://www.dropbox.com/s/ppjfflhf3j5yzh2/MarlinV2.0%20SKRV1.1%20instruction.docx?dl=0

Product Features

  • Using 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improved
  • Reserved extended port SERVOS of PWM signal to support BL Touch
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • The SPI working mode of the TMC2130 driver and the UART working mode driven by the TMC2208, which eliminates complex wiring process and can be used by simple unplugging jumper cap
  • SKR V1.3 board has CE Certification to adopt 4-Layer PCB with “Gold deposition technology” which capability is more stable and better heat dissipation

Visit The Website For More Information…

WINSINN Titan Extruder Bowden Hotend Drive Feed Kit for RepRap Prusa i3 J-Head V6 Makerbot MK8 MK10-3D Printer Universal Upgrade Part 1.75mm 3mm Nozzle Filament


►This is a Optimized version of 3D Printer Extruder. It is very light and compact. It can use a lighter motor, any Bowden-type 3D printer can become a powerful, reliable little beast. It is easy to manually squeeze, remove, load and unload Filament.
At the same time, You only need a hex wrench, you will be able to within a minute to remove the Titan, regardless of the opening and assembly are very easy and fast.

—————————————————————————————————————

►Installation Points: The top surfaces of the two gear s must be flush adjust the pinion accordingly

►We have done thousands times of tests, including strength testing, time testing and so on. It really works well. Let’s try it:))

—————————————————————————————————————

Package include:
►1 x WINSINN Extruder Full kit (All Accessories show as Picture 2)
►Note: This Kit NOT Included Motor, V6 Hotend, Titan Aero

Product Warranty:

-WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty.
-If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.

Product Features

  • ✔️Compatible with E3D-V6 Hotend and Titan Aero Upgrade Kit
  • ✔️High quality Titan extruder, Very easy to upgrade your printer
  • ✔️Filament:1.75mm 3mm PLA / ABS / Flexible / other
  • ✔️Suitable For Remote and Short distance
  • ✔️Note: This Kit NOT Included Motor, V6 Hotend, Titan Aero

Visit The Website For More Information…

Creality 3pcs/Lots Limit Switch 3D Printer Part for CNC 3D Printer RepRap Makerbot Prusa Mendel RAMPS 1.4 Board Ender 3 CR-10S Series

Description:
Made of premium metal material for durable use.
With trigger indicator light, plug and play, convenient in use.

Features:
– Material: Metal
– Size: 2x2x1cm
– Constant on mechanical limit switch.
– Small sized, easy to install.
– A great accessory for 3D printer.

Package Including:
3 × Limit Switches

Product Features

  • Compatible with all Creality 3D Printer
  • Number of Pins: 3
  • 3D Printer Accessories Limit Switch 3Pin N/O N/C control easy to use Micro Switch
  • 100% Creality Original
  • Package Included: 3 PCS * Limit Switch

Visit The Website For More Information…