WINSINN 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.6 Upgraded Mosfet + 5Pcs DRV8825 Stepper Motor Driver + LCD 12864 for Arduino Reprap


Ramps 1.6 board:

-Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.

DRV8825 Driver:

-Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
-Six different stepping resolutions: full, half, 1/4,1/8,1/16,1/32
-Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate
-Automatic current decay mode detection / selection
-Thermal shutdown circuit, undervoltage lockout, crossover current protection
-Ground short-circuit protection and load short-circuit protection

Mega 2560 R3:

-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limits):6-20V
-Digital I/O Pins:54 (of which 14 provide PWM output)
-Analog Input Pins:16
-DC Current per I/O Pin:40 mA
-DC Current for 3.3V Pin:50 mA
-Flash Memory:256 KB of which 4 KB used by bootloader
-SRAM:8 KB
-EEPROM:4 KB

—————————————————————————————————————

Package include:
►1 x RAMPS 1.6 Board
►1 x Mega 2560 R3 Board
►1 x 12864 LCD Display Controller
►1 x LCD Smart Adapter
►5 x DRV8825 Stepper

———————————————————————————————————————

►Note:
►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • ✔️DRV8825 driver board widely used in 3D printers and small CNC machines. It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance. It suitable for driving below 8.2V ~ 45V 2.5A stepper motor, And had Six different stepping resolutions: full, half, 1/4 ,1/8, 1/16, 1/32.
  • ✔️12864 LCD: The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using “smart adapter” included. This panel connect your RAMPS 1.6, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller.
  • ✔️This kit includes a complete set of the most common and useful components that can be used by all tech-savvy people out there to build their own printer controller. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • ✔️Product Warranty: WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
  • ✔️Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be samller than 200W.

Click Here If You Need More Detailed Info…

3pcs 3D Printer Stepper Motor Parallel Module with/w Cable for Double Z Axis Dual Z Motors for Lerdge 3D Printer Board

This module is only used for parallel connection of the motor terminals. One drive drives two motors. It is only suitable for parallel connection of small printers or small current motors. (The current is evenly divided when the same motor is used in parallel).

Package includes
3*Stepper Motor parallel module
3*Pcs cables

Product Features

  • New Dual Z Stepper Motor Adapter Parallel Module Diverter Expanding Flow Board Diffuser Splitter
  • Special design for stepper motor-side parallel, a driver drives two motors, put them in-line (series) with the motor
  • Comes with a 4 pin cable (4 inch), easy to connect
  • Only for mini printers or small current motors in parallel (with the same motor in parallel, the current are divided evenly);
  • Easy to connect

Detailed Information available on our Homepage…

ARQQ TL Smoother Addon Module for Pattern Elimination Motor Clipping Filter 3D Printer Stepper Motor Drivers (Pack of 3pcs)

Package Listing:
3x TL-Smoother Clipping Filter

Product Features

  • The TL-Smoother is an addon module for 3D printer stepper motor drivers
  • Lower vibration lower noise smoother result
  • The board provides flyback diodes (freewheeling diodes) for the motor outputs
  • Also protected against induction voltages in the unpowered state of the driver
  • You will got smoother movement especially on the delta-style 3Dprinter under DVR8825 stepper drivers and A4988/2 drivers

Visit The Website For More Information…

nouler Juler 3D Printer Parts Stepper Motor Nema 42 1.8 Deg 4Wires 60Mm 1.5A Bipolar

Welcome to our shop, your support is our greatest motivation. All products are sold at low prices, we guarantee quality.

Description:

– -Holding torque: 700mN.m MIN .

– -Rated Current/phase: 1.5A; Rated Voltage: 3.6V DC

– -Portable and durable, lightweight, great performance.

– -Widely used in engraving machine, printer, medical equipment, embroidery machine, textile automation,printing,packaging and other industries automation equipment.

– -Fits for 3D printers, monitor equipment, medical machinery, textile machinery and so on.

Specification:

– Material: Metal

– Size: 75x35x45mm/2.95×1.37×1.77inch

– Step Angle: 1.8°

– Motor Length: 60mm

– Holding Torque: 0.8N.m

– Rated Current/phase: 1.5A

– Rated Voltage: 3.6V DC

– Phase Resistance 1.8±10%

– Weight: 480g

Package Includes:

1 Piece 3D Printer MotorNote:

Please allow slightly difference due to manual measurement.

Color may be slightly different since different monitor.

Product Features

  • Phase Resistance: 1.8Ω±10%
  • Rated Current/phase: 1.5A
  • Motor Length: 60mm
  • Step Angle: 1.8°
  • Weight: 480g

Visit The Website For More Information…