HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

Wangdd22 3D Printer kit RAMPS 1.4 Control Panel Printer Control Reprap MendelPrusa +5 pcs A4988 StepStick Stepper Motor Driver Module with Heatsink for 3D Printer.

Using This suite (1pcs RAMPS 1.4 Control Panel Printer Control Reprap MendelPrusa +5 pcs A4988 Driver Module with Heatsink) on your Arduino-compatible MEGA shield for easy service,part replacement,upgrade-ability and expansion.

A4988:
Simple step and direction control interface.
Can interface directly with 3.3 V and 5 V systems.
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout.
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates.
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage.
Built-in regulator.(no external logic voltage supply needed)

RAMPS 1.4 Controller:
Expandable to control other accessories.
3 Mosfets for heater / fan outputs and 3 thermistor circuits.
Fused at 5A for additional safety and component protection
Heated bed control with additional 11A fuse.
Fits 5 Pololu stepper driver boards.
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
I2C and SPI pins left available for future expansion.
All the Mosfets are hooked into PWM pins for versatility.
Servo style connectors are used to connect to the end stops, motors, and LEDs. These connectors are rated for 3A, very compact, and globally available.
SD Card add on available.
LEDs indicate when heater outputs on.
Option to connect 2 motors to Z for Prusa Mendel.

Tips:
When inserting the A4988 module,make sure the direction is right.

Package include:
1 x RAMPS 1.4 Controller Board
5 x A4988 Stepstick Driver with Heat Sink

Product Features

  • RAMPS 1.4 expansion board as a driver expansion board, can be used for engraving machines, 3D printers.and It is a total of five slots, can drive five A4988 stepper motor.
  • Stepper motor wiring as follows: 2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.
  • Flexible set: 1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • Each road stepper motors only need two IO ports.
  • Step five selectable modes: full , 1/ 2, 1 / 4, 1 / 8 and 1/ 16

Click Here If You Need More Detailed Info…

Oyep-5 PCS DRV8825 StepStick Stepper Motor Drivers for 3D Printer Electronics, CNC Machine or Robotics

The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications.

The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).

DRV8825 Technical Specs:

– Simple step and direction control interface
– Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
– Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
– 45 V maximum supply voltage
– Built-in regulator (no external logic voltage supply needed)
– Can interface directly with 3.3 V and 5 V systems
– Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
– Short-to-ground and shorted-load protection
– 4-layer, 2 oz copper PCB for improved heat dissipation
– Exposed solderable ground pad below the driver IC on the bottom of the PCB
– Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects

Package contents:

– 5 x DRV8825 Stepper drivers with self stick heatsinks

Product Features

  • Simple step and direction control interface
  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step. Output drive capacity of up to 35 V and ± 2 A
  • Adjustable current control lets you set the maximum current output with a potentiometer
  • Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
  • Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection

Visit The Website For More Information…

Kuman 3D Printer Kit Controller RepRap RAMPS 1.4 Controller Board + 5pcs A4988 StepStick Stepper Motor Driver Module + Heat Sink KY57

Using This suite (1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service,part replacement,upgrade-ability and expansion.

Feature

RAMPS 1.4 Controller
Expandable to control other accessories.
3 Mosfets for heater / fan outputs and 3 thermistor circuits.
Fused at 5A for additional safety and component protection
Heated bed control with additional 11A fuse.
Fits 5 Pololu stepper driver boards.
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
I2C and SPI pins left available for future expansion.
All the Mosfets are hooked into PWM pins for versatility.
Servo style connectors are used to connect to the end stops, motors, and LEDs. These connectors are rated for 3A, very compact, and globally available.
SD Card add on available.
LEDs indicate when heater outputs on.
Option to connect 2 motors to Z for Prusa Mendel.

A4988
Simple step and direction control interface.
Can interface directly with 3.3 V and 5 V systems.
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout.
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates.
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage.
Built-in regulator.(no external logic voltage supply needed)

Package include
1 x RAMPS 1.4 controller board
5 x A4988 Stepstick Driver
5 x Heat Sink

Product Features

  • Flexible set: 1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • RAMPS 1.4 expansion board as a driver expansion board, can be used for engraving machines, 3D printers.and It is a total of five slots, can drive five A4988 stepper motor.
  • Each road stepper motors only need two IO ports.
  • Stepper motor wiring as follows: 2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.
  • Note: When inserting the A4988 module,make sure the direction is right.

Click Here If You Need More Detailed Info…