Laliva 3D Printer – DC 12V Soil Moisture Sensor Relay Control Module Automatic Watering of The Humidity Starting Switch

Product Details
12V soil moisture sensor controller module Lower humidity start automatic watering
Humidity is below the set humidity start means that when soil moisture is below the set humidity , the relay will automatically pull, start spraying , water pumps , etc. do humidifying action reaches the set humidity is automatically stopped.
Purpose:
Adjustable via potentiometer control soil moisture threshold , which can automatically vegetable garden , garden automatic watering , household pots of soil moisture control , electronic game , etc., with a power relay , can control high current devices , less than the set humidity automatically start relay , more than the set humidity automatically disconnected , and a delay function to resolve without delay the humidity critical state relay flickered question is a simple and practical soil moisture control system.
Product Descriptions:
1 using the company\’s high-quality soil to make the soil moisture sensor detection surface is nickel plated, has widened sensing area can improve conductivity, prevent rust easily contact with soil problems and prolong life .
(2) products can be controlled over a wide range of soil moisture , adjustable via potentiometer control the corresponding threshold , the humidity is below the set value, the relay starts , higher than the set value, the relay is switched off .
3 product with a delay function , delay 3-5 seconds , when the humidity in the critical condition is detected , the relay does not flicker , flicker occurs .
4 high-quality products using Songle relay can withstand the load of 1500W , meet the requirements of most people .
5 products with a power indicator and relay instructions .
Electrical parameters:
Supply voltage : 12VDC Input current : more than 100ma
Load : 250V 10A AC or DC 30V 10A (below a current of this range can be used)
Module for use:
1 soil moisture sensor for detection .
2 modul

Product Features

  • 1 using the company\’s high-quality soil to make the soil moisture sensor detection surface is nickel plated, has widened sensing area can improve conductivity, prevent rust easily contact with soil problems and prolong life .
  • (2) products can be controlled over a wide range of soil moisture , adjustable via potentiometer control the corresponding threshold , the humidity is below the set value, the relay starts , higher than the set value, the relay is switched off .
  • 3 product with a delay function , delay 3-5 seconds , when the humidity in the critical condition is detected , the relay does not flicker , flicker occurs .
  • 4 high-quality products using Songle relay can withstand the load of 1500W , meet the requirements of most people .
  • 5 products with a power indicator and relay instructions .

Click Here For More Information

3PCS Mechanical End Stop Limit Switch With Cable For 3D Printer – 3D Printer & Supplies 3D Printer Accessories – 3x End Stop Limit Switch, 3x Cable

3PCS Mechanical End Stop Limit Switch With Cable For 3D Printer – 3D Printer & Supplies 3D Printer Accessories – 3x End Stop Limit Switch, 3x Cable,
Features: 1. Not easy to pull off, plug it convenient, for ease of use, plug the other to do the one, you can use the direct plug.
2. Automatic Control, 5A125VAC~5A250VAC
3. Temperature resistance: 80 centigrade
4. Red line connecting VCC (ramps of +)
5. Black wire connecting GND (ramps of -)
6. Cable length: About 70cm
Package included:
3x End Stop Limit Switch
3x Cable

Product Features

  • 3D Printer & Supplies 3D Printer Accessories – 2. Automatic Control, 5A125VAC~5A250VAC
  • Temperature resistance: 80 centigrade
  • Red line connecting VCC (ramps of +)
  • Black wire connecting GND (ramps of -)
  • 3PCS Mechanical End Stop Limit Switch With Cable For 3D Printer – 3D Printer & Supplies 3D Printer Accessories – 3x End Stop Limit Switch, 3x Cable

Detailed Information available on our Homepage…

10PCS 220V/110V 5A Power Outlet Socket With Switch And 6A Fuse For 3D Printer – 3D Printer & Supplies 3D Printer Accessories – 10 x Quartz clock movement kit

10PCS 220V/110V 5A Power Outlet Socket With Switch And 6A Fuse For 3D Printer – 3D Printer & Supplies 3D Printer Accessories – , , , , , , 10 x Quartz clock movement kit, , , , , , Notice:, , , , ,
Features: Color: black
Voltage: 110/220V
Current: 15A (comes with a 6A fuse)
Package  Included:
10 x Power Outlet

Product Features

  • 3D Printer & Supplies 3D Printer Accessories – Voltage: 110/220V
  • Current: 15A (comes with a 6A fuse)
  • Package ;Included:
  • 10 x Power Outlet
  • 10PCS 220V/110V 5A Power Outlet Socket With Switch And 6A Fuse For 3D Printer – 3D Printer & Supplies 3D Printer Accessories – 10 x Quartz clock movement kit

Detailed Information available on our Homepage…

WGCD 10 PCS Endstop Mechanical Limit Switch with Cable for 3D Printer RAMPS Prusa Mendel RepRap CNC Arduino Mega 2560

Specification:
Connections:
1, Red Line Connecting VCC (Ramps of +)
2, Connect the black wire GND (Ramps of -)
3, Green Line connection SIGNAL (Ramps in s)
Cable Type: 22 AWG
Cable Length: 70cm
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.

Package Csontent:
10 * Mechanical End Stop Endstop Limit Switch

Product Features

  • Mechanical endstop limit switches with 22AWG Cable for 3D Printer RAMPS 1.4 Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280.
  • Red line connecting VCC (ramps of +), Connect the black wire GND (ramps of -), Green Line connection SIGNAL (ramps in s)
  • Easy to install, common styles, replacement endstop for RAMPS 1.4, CNC and other 3D printer controllers.
  • Cable Length: 70cm/27.55inches
  • Package Content: 10 * Mechanical End Stop Endstop Limit Switch with Cable.

Visit The Website For More Information…