BIGTREETECH TFT24 V1.1 Touch Screen Display Compatible 12864LCD 3D Printer Parts VS MKS TFT2.4 for SKR PRO SKR V1.3


※【Introduction】: BIGTREETECH TFT24-V1.1 is a small volume ultra-clear 3D printer display board. It can work in two modes.
The board is launched by the 3D printing team of Shenzhen BIGTREE Technology co., LTD. This board can replace LCD12864 for use.

※【Product Advantages】:

1 ) ARM Cortex-M3 series STM32F105RCT6 chip with 32-bit CPU 72MHz;
2 ) Upgrade the firmware by SD card. It is easy and convenient to operate.
3 ) This display board has higher compatibility. Users can select two work modes, they are UART serial port screen mode and 12864 screen mode.
4 ) Serial port screen mode supports two printing modes: SD card and U disk.

※【Product Parameters】:
Appearance size: 105*46mm
Installation size: detail information in TFT24-V1.1-SI
Microprocessor:STM32F105RCT6
Power Input:DC5V

1) When using 12864 screen mode, connect the port EXP1 and EXP2 to the motherboard. There is no touch function in this mode.
2) When using serial port screen mode, connect with TFT or aux-2 on the motherboard via RS232. In this mode, there is touch function.
3) The two modes correspond to two different firmwares, please connect wires according to the mode type of the flashed firmware.
※【Notes】:
1. The name of the firmware file in the SD card cannot be changed. (including capital and small letters)
2. Wiring process must be under the precondition of power outages. Users must check the correct connection of the circuit and the correct insertion of the drive before turning on electricity.
Pay attention to the wiring sequence and do not insert the wire inversely. Please refer to PIN file for detailed line order. If you have any questions, pls fell free to contact with us 【bigtreetech-us(Mailbox symbol)outlook.com】change Mailbox symbol to @

Product Features

  • ✓1.【Appearance size】: 105*46mm
  • ✓2.【Installation Size】: 100.08*41.1mm
  • ✓3.【Working modes】 :UART Serial Port Touch Screen and 12864 LCD can be selected;Microprocessor: STM32F105RCT6
  • ✓4.【How to connect with the SKR series or MKS series board】: https://www.youtube.com/watch?v=TeRSGmcd8A8
  • ✓5.【TFT24 V1.1 Manual and Firmware/Hardware】: https://github.com/bigtreetech/BIGTREETECH-TFT24-V1.1

Visit The Website For More Information…

BIQU 3D Printer Part SKR Mini V1.1 32bit Control Board Marlin 2.0 Open Source Compatible with Ramps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers (DC Connector)

SKR Motherboard Parameters:
Appearance size: 90*70mm
Mounting size: 80*60mm
Microprocessor: ARM Cortex-M3 CPU
Input voltage: DC12V-DC24V 5A-12A
Motor driver: support TMC2208, TMC2130, ST820, LV8729, DRV8825, A4988
Motor drive interface: X, Y, Z, E0, Four(Serial Dual Z-axis), Up to 256 subdivisions
Display: 2.8 “TFT, 3.5” TFT
Temperature Sensor Interface:TH0、TB, two 100K NTC thermistor

Notice:
When the SKR motherboard is electricity , the red light D2 in the lower right corner will light up, indicating that the power supply is normal. The middle of the Board DC SEL is the power selection end
1, when using USB to power the motherboard, short circuit cap should be used to connect +5V and USB Pins
2, when using 12v-24v power supply, short circuit cap shall be used to connect +5V and INT pins

Attention: Can be connected [12v-24v power], [USB] at the same time , the printing process must be connected with a short circuit cap +5V And INT
3,The Board 5V SEL must be connected to INT and +5V two pins before it going to print 4,It must be connected with an external hot bed MOS Extension Module if you need to use with Heatbed, it is very significant that Motherboard can not connect with heat bed directly.

How to use
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1,The driver can be obtained from our open-source website: https://github.com/bigtreetech, named by “mapleDrv” file
2. After installing the driver, connect the computer and SKR motherboard with USB cable
If you need more information about this Board please contact us

Product Features

  • Using 32bit frequency 72MHz ARM Cortex-M3 series STM32F103RCT6 main Microprocessor, the performance has been greatly improved
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • SKR Mini V1.1 Board adopt “Gold Finish” process which capability is more stable and better heat dissipation
  • Support 2.8 and 3.5 Inch Touch Screen,2004LCD (but don’t Support 12864 LCD)

Visit The Website For More Information…

BIQU 3D Printer Part SKR V1.1 32-Bit with ARM CPU Control Board Open Source Smoothieboard Support TMC2130 TMC2208 Driver 12864 LCD

product Parameter
Microprocessor: ARM Cortex-M3 CPU
Input voltage: DC12V-DC24V  5A-15A
Motor Driver: Supports TMC2208, TMC2130, LV8729, DRV8825, A4988 Etc., can be externally connected to the motor drive
Motor drive interface: X, Y, Z, E0, E1, five channels (each channel has a re-expandable interface), up to 256 subdivisions
Temperature sensor interface: TH0, TH1, TB, 3 channels 100K NTC (thermal resistance) Display: 2.8 inch TFT, 3.5 inch TFT,LCD12864
PC communication interface: square USB, easy to plug and unplug, communication baud rate 115200
Support file format: G-code
Support machine structure: XYZ, delta, kossel, Ultimaker, corexy
Recommended software: Cura, Simplify3D, pronterface, Repetier-host, Makerware

Packing List:
1*SKR Board 1*cable

Product Features

  • ARM-class Cortex-M3 series LPC1768 master chip with 32-bit main frequency 100M,Can be greatly improved
  • Acceptable 24V input, the hot bed current can be reduced to 1/4 under the same power, effectively solving the heating problem of the hot bed MOS tube
  • Upgrade the firmware by SD card, which is easy and convenient to operate
  • Use the configuration file to set the driving current mode, avoid manual adjustment of the current to cause the burned drive, convenient, safe and reliable
  • Support functions:  Non-trace resumption after power off, run out filament ,and auto shut down

Visit The Website For More Information…

Ywillink Engraving Machine Smoothieboard 5X V1.1 Mainboard Part for 3D Printer

Feature:
Smoothieboard is an Open-Source Hardware CNC controller designed by the Smoothie community to run the Smoothieware firmware.
Its main design goals are:
Uses as powerful hardware as possible at the time
Can control several machine types ( 3D printers, lasers, CNC mills/routers )
Easy to setup and use
Easy to do weird, new and exciting things with
Easy to develop for
This page is for v1, the first version of the Smoothieboard hardware.

Microcontroller:
The board uses the LPC1769 microcontroller, an ARM Cortex-M3 chip :
32-bit architecture
120Mhz frequency
512kB ROM ( program space )
64kB RAM ( execution memory )
Compared to lots of other boards, this allows for faster/smoother movement, more features and more extensibility.
The board runs the Smoothie firmware, which has been designed and perfected to take best advantage of the hardware, to make the board easy to configure and use, and to add cool features.Model Number: Item Type:–Motherboard
Included:
1 x Smoothieboard 5X V1.0
5 x Heat Sink
1set x Terminals
1 set x Jump Wire
1 set x Needles

Product Features

  • Smoothieboard is an Open-Source Hardware CNC controller designed by the Smoothie community
  • Compared to lots of other boards, this allows for faster/smoother movement, more features and more extensibility.
  • The board runs the Smoothie firmware, which has been designed and perfected to take best advantage of the hardware, to make the board easy to configure and use, and to add cool features.
  • Can control several machine types ( 3D printers, lasers, CNC mills/routers )
  • Uses as powerful hardware as possible at the time

Visit The Website For More Information…