BIGTREETECH DIRECT BTT SKR Mini E3 V1.2 Control Board + TFT35-E3 V3.0 Touch Screen Compatible TFT35 12864LCD Display WiFi 3D Printer Parts for Creality Ender 3


Introduction:
【BIGTREETECH SKR-mini-E3 】motherboard is the 3D batting of ShenZhen BigTree Technology CO.,LTD
An ultra-silent, low-power, high-quality 3D printer master board launched by the printing team.

Specially for Ender 3 printer to update.

More detailed information about SKR MINI E3 you can visit this website:
https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3

【BIGTREETECH TFT35-E3 V3.0】 is a medium size, dual-mode, ultra-clear 3D printing machine display launched by the 3D printing
team of Shenzhen BIGTREE Technology CO., LTD., which can perfectly replace the original LCD screen of Ender3 printer.
More detailed information about SKR MINI E3 you can visit this website:
https://github.com/bigtreetech/BTT-TFT35-E3-V3.0

Product Features

  • 【 SKR MINI V1.2】: Perfect upgade of Ender 3 machine motherboard
  • 【 SKR MINI V1.2 Stepper motor】: Integration of TMC2209 UART Mode
  • 【TFT35 E3 V3.0】:Touch Screen compatible 12864LCD Display
  • 【 SKR MINI E3 Firmware】: https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3
  • 【TFT35 E3 V3.0 Firmware】:https://github.com/bigtreetech/BTT-TFT35-E3-V3.0

Visit The Website For More Information…

BIGTREETECH DIRECT TMC5160 V1.2 SPI Stepper Motor Driver 6-Layer Board VS TMC2208 TMC2209 3D Printer Parts for Ender 3/5 SKR V1.3 Pro


※【TMC5160】
TMC5160 is a high-power stepper motor driving control chip, which has externally expanded power MOS tube, the the maximum current can reach 20A, low heat when working

※【 Product Advantages】
(1)External power MOS tube can support larger current, the maximum current can reach 20A (because the module is limited by area, the current cannot exceed)
(2)Super-mute mode
(3)Low calorific value
(4)can prevent motor shake
(5)not easy to lose step
(6)can drive 57 stepper motor
Special note: Currently only firmware of Marlin 2.0 and above supports the SPI mode of TMC5160

※【 Precautions】
1). Always disconnect the power supply before installing the driver to prevent the driver from burning.
2). Be sure to confirm the direction of the driver before installing the driver. Prevent the driver from burning due to reverse connection.
3). Please do not plug and unplug the driver module when power is on to avoid damage.
4). When installing the heat sink, please be careful not to contact the heat sink and the pin header to prevent short circuit.
5). The product is sensitive to static electricity, please handle it carefully when using, it is best to remove the package when using. If you have any question within using, pls feel free to contact with us【mika”Mail symbol”bigtree-tech.com】 change the Mail symbol to @

Product Features

  • ✓1.Driver chip: TMC5160-WA;
  • ✓2.Product size: 15.3mm * 20.4mm;
  • ✓3.Power supply voltage (VM): 8V — 35V;
  • ✓4.Maximum current: 4.4A (sampling resistance determines the maximum current);✓✓Maximum breakdown: 256; ✓✓Working mode: SPI mode
  • ✓5.Manual:https://github.com/bigtreetech/BIGTREETECH-TMC5160-V1.0

Visit The Website For More Information…

BIGTREETECH SKR Mini E3 V1.2 Control Board 32Bit with TMC2209 UART Driver 3D Printer Parts Cheetah for Creality Ender 3

Features:

Carries highly modular open source firmware Marlin 2.0, which facilitates user DIY and secondary development;

PCB board wiring is rigorous and beautiful, and has been specially optimized for heat dissipation.

Special power chip is used to support 12-24V power input.

Acceptable 24V input, the same power can reduce the hot bed current to 1/4, effectively solve the hot bed.MOS tube heating problem;

Upgrading firmware by SD card makes operation simple and convenient.

Firmware is used to set the driving current so as to avoid burning out the driving caused by manual regulation of the current.Convenient, safe and reliable;

Product Features

  • 1)ARM Cortex-M3 Series STM32F103RCT6 Master Controller with 32-bit Main Frequency of 72MHz Chip;
  • 2) Supporting display :2.8 inch, 3.5 inch color touch screen and Ender3 printer LCD12864 screen;
  • 3)Support BLtouch, RGB color lamp, block detection, shutdown and other functions;
  • 4) Integrate UART mode of TMC2209 to simplify debugging of motherboard and driver.Reserve expansion ports for TMC2209 pins to facilitate users to use DIAG instead of Endstop.
  • 5) Https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3?spm=a2g0o.detail.1000023.20.22b67ce5URWusv

Visit The Website For More Information…

Gowoops 3D Printer Motherboard MKS MINI V1.2 RepRap + 2.8 Inch Full Color Touch Screen LCD MKS TFT28 V1.2

MKS MINI V1.2 Board User Manual: http://osoyoo.com/2016/09/21/mks-mini-v1-2-3d-printer-board-circuit-connection-graph-and-firmware-installation-guide/

MKS-TFT28 Touch Screen User Manual: http://osoyoo.com/2016/07/25/mks-tft-2-8-touch-screen/

Caution:
1) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) .
2) Always double check power wire is properly installed. If you do not follow above move, you can damage the control board and your 3D printer.

MKS MINI V1.2 printing integrated mainboard:

MKS MINI is a feature all-in-one electronics solution for Reprap and other CNC devices.
It features an onboard ATmega2560.
It’s four motor outputs are powered by DRV8825 stepper drivers.
The board can use the same firmware as Ramps1.4.
The mounting hole locations is the same as Arduino Mega2560.
The power supply with 7805, more stable and reliable than the 1117, but only supports 12V.USB to serial modules is 16U2, the same as Arduino Mega2560.Without hot bed heating output, but has bed thermal interface and bed control signal interface.

MKS-MINI is suitable for One-Extruder and no bed printing.

LCD Full Color Touch Screen MKS TFT28 V1.2
Set the Boot
1) Must: After the first boot into -> Settings -> connection, select the firmware used by the baud rate, it can be used.
2) You must: Go to -> Settings -> type, select the printer type, only Delta and the other two options.
3) Optional: You can enter -> Settings -> touch screen calibration, improve the accuracy of the touch screen.

Package Included:
1 x 2.8 Inch Full Color Touch Screen MKS TFT28 V1.1 For 3D Printer
1x MKS MINI V1.2 Board

Product Features

  • MKS MINI V1.2 Board: Arduino MEGA compatible Atmega2560 processors are compatible with all RAMPS class firmware. Easy DISPLAY + SD-CARD connector, RepRapDiscount. SmartController compatible pin header on board. Firmware can use the same configuration as ramps1.4.
  • MKS MINI V1.2 Board: 2x temperature ADC connectors for thermistors, up to 4 motor driver with DRV8825. 2x PWM capable power mosfet outputs with voltage selector for MainPower.(Extruder0,Fans). 6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax. 4 layers PCB, optimize heat dissipation. Recoverable fuse for short-circuit protection.
  • MKS-TFT28 is an independent color touch product suitable for the use of open source 3D printers, support U disk and SD card. The main control program without need modification, plug and play, support Marlin, Repetier, Smoothieware firmware.
  • MKS-TFT28 support power failure renew,power failure preservation. The main control program without need modification, plug and pla. Can increase the custom function button. Provide continuous software upgrade, upgrade method is simple.
  • MKS-TFT28 can be used on Ramps1.4 and MKS Base , MKS Gen , MKS Mini and a series of motherboard. Boot logo and all buttons, such as interface can be designed by ourselves.

Visit The Website For More Information…